Pass Your CCNP Enterprise 350-401 Exam on Jun 23, 2022 with 543 Questions [Q185-Q204]

Pass Your CCNP Enterprise 350-401 Exam on Jun 23, 2022 with 543 Questions

350-401 Free Exam Study Guide! (Updated 543 Questions)

Related Certification: CCNP Enterprise

Enterprise networking continues to witness massive growth ever since Cisco introduced a new certification curriculum in early 2020. This is best shown by the increasing popularity of the Cisco CCNP Enterprise certification, which does much more than just equipping you with vital IT skills. The new CCNP Enterprise training embodies success with enterprise networking technologies and to obtain it, you must pass two exams: the aforementioned Cisco 350-401, which is a core validation, and one additional concentration exam. That being said, the full list of the concentration tests associated with this learning path includes 300-410, 300-415, 300-420, 300-425, 300-430, and 300-435 exams.

NO.185 Which unit measures the power of a radio signal with reference to 1 milliwatt?

 dBw

 dBm

 mW

 dBi

dBm is an abbreviation for “decibels relative to one milliwatt,” where one milliwatt (1 mW) equals 1/1000 of a watt. It follows the same scale as dB. Therefore 0 dBm = 1 mW, 30 dBm = 1 W, and -20 dBm = 0.01 mW

NO.186 A GRE tunnel is down with the error message %TUN-5-RECUR DOWN:

Which two options describe possible causes of the error? (Choose two)

 There is link flapping on the tunnel

 Incorrect destination IP addresses are configured on the tunnel

 The tunnel mode and tunnel IP address are misconfigured

 There is instability in the network due to route flapping

 The tunnel destination is being routed out of the tunnel interface

NO.187 Which action is a function of VTEP in VXLAN?

 tunneling traffic from IPv6 to IPv4 VXLANs

 allowing encrypted communication on the local VXLAN Ethernet segment

 encapsulating and de-encapsulating VXLAN Ethernet frames

 tunneling traffic from IPv4 to IPv6 VXLANs

NO.188 When configuration WPA2 Enterprise on a WLAN, which additional security component configuration is required?

 NTP server

 PKI server

 REDIUS server

 TACACS server

NO.189 Refer to the exhibit. Which two statements about the EEM applet configuration are true? (Choose two.)

 The EEM applet runs before the CLI command is executed.

 The EEM applet runs after the CLI command is executed.

 The EEM applet requires a case-insensitive response.

 The running configuration is displayed only if the letter Y is entered at the CLI.

When you use the sync yes option in the event cli command, the EEM applet runs before the CLI command is executed. The EEM applet should set the _exit_status variable to indicate whether the CLI command should be executed (_exit_status set to one) or not (_exit_status set to zero).
With the sync no option, the EEM applet is executed in background in parallel with the CLI command.
Reference: https://blog.ipspace.net/2011/01/eem-event-cli-command-options-and.html

NO.190 Refer to the exhibit.

Which command must be applied to Routed to bring the GRE tunnel to an up/up state?

 Router1(config)#interface tunnel0

 Router1(config-if)#tunnel source GigabitEthernet0/1

 Router1(config-if)#tunnel mode gre multipoint

 Router1(config-if)#tunnel source Loopback0

Explanation
In order to make a Point-to-Point GRE Tunnel interface in up/up state, two requirements must be met: + A valid tunnel source (which is in up/up state and has an IP address configured on it) and tunnel destination must be configured + A valid tunnel destination is one which is routable. However, it does not have to be reachable.

NO.191 Refer to the exhibit.

An engineer must modify the access control list EGRESS to allow all IP traffic from subnet 10.1.10.0/24 to
10.1.2.0/24. The access control list is applied in the outbound direction on router interface GigabitEthemet 0/1.
Which configuration commands can the engineer use to allow this traffic without disrupting existing traffic flows?
A)

B)

C)

D)

 Option A

 Option B

 Option C

 Option D

NO.192 An engineer must protect their company against ransom ware attacks. Which solution allows the engineer to block the execution stage and prevent file encryption?

 Use Cisco AMP deployment with the Malicious Activity Protection engineer enabled.

 Use Cisco AMP deployment with the Exploit Prevention engine enabled.

 Use Cisco Firepower and block traffic to TOR networks.

 Use Cisco Firepower with Intrusion Policy and snort rules blocking SMB exploitation.

Explanation
Ransomware are malicious software that locks up critical resources of the users.
Ransomware uses well-established public/private key cryptography which leaves the only way of recovering the files being the payment of the ransom, or restoring files from backups.
Cisco Advanced Malware Protection (AMP) for Endpoints Malicious Activity Protection (MAP) engine defends your endpoints by monitoring the system and identifying processes that exhibit malicious activities when they execute and stops them from running. Because the MAP engine detects threats by observing the behavior of the process at run time, it can generically determine if a system is under attack by a new variant of ransomware or malware that may have eluded other security products and detection technology, such as legacy signature-based malware detection. The first release of the MAP engine targets identification, blocking, and quarantine of ransomware attacks on the endpoint.
Reference: https://www.cisco.com/c/dam/en/us/products/collateral/security/ampfor- endpoints/white-paper-c11-740980.pdf

NO.193 In an SD-Access solution what is the role of a fabric edge node?

 to connect external Layer 3- network to the SD-Access fabric

 to connect wired endpoint to the SD-Access fabric

 to advertise fabric IP address space to external network

 to connect the fusion router to the SD-Access fabric

Explanation
+ Fabric edge node: This fabric device (for example, access or distribution layer device) connects wired endpoints to the SDA fabric.

NO.194 What is the difference between CEF and process switching?

 CEF processes packets that are too complex for process switching to manage.

 CEF is more CPU-intensive than process switching.

 CEF uses the FIB and the adjacency table to make forwarding decisions, whereas process switching punts each packet.

 Process switching is faster than CEF.

NO.195 Refer to the exhibit.

Which IPv6 OSPF network type is applied to interface Fa0/0 of R2
by default?

 multipoint

 broadcast

 Ethernet

 point-to-point

Explanation
The Broadcast network type is the default for an OSPF enabled ethernet interface (while Point-to- Point is the default OSPF network type for Serial interface with HDLC and PPP encapsulation).
Reference: https://www.oreilly.com/library/view/cisco-ios-cookbook/0596527225/ch08s15.html

NO.196 Drag and drop the threat defense solutions from the left onto their descriptions on the right.

Explanation

NO.197 Drag and drop the characteristics from the left onto the correct routing protocol types on the right.

Explanation
OSPF: SEGMENT, LINK STATE, TABLES
EIGRP: UNEQUAL PATH, DISTANCE VECTOR, METRIC

NO.198 An engineer creates the configuration below. Drag and drop the authentication methods from the left into the order of priority on the right. Not all options are used.

NO.199 Refer to the exhibit.

After implementing the configuration 172.20.20.2 stops replaying to ICMP echoes, but the default route fails to be removed. What is the reason for this behavior?

 The source-interface is configured incorrectly.

 The destination must be 172.30.30.2 for icmp-echo

 The default route is missing the track feature

 The threshold value is wrong.

NO.200 Drag and drop the LISP components on the left to the correct description on the right

Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_lisp/configuration/xe-3s/irl-xe-3s-book/irloverview.html#GUID-92481C7B-F44D-4D8C-8085-A2E98530CA50

NO.201 Drag and drop the DHCP messages that are exchanged between a client and an AP into the order they are exchanged on the right.

Explanation

Table Description automatically generated
There are four messages sent between the DHCP Client and DHCP Server: DHCPDISCOVER, DHCPO FFER, DHCPREQUEST and DHCP This process is often abbreviated as (for Discover, Offer, Request, Acknowledgement).

NO.202 Refer to the exhibit.

Which statement about the OPSF debug output is true?

 The output displays all OSPF messages which router R1 has sent to received on interface Fa0/1.

 The output displays all OSPF messages which router R1 has sent or received on all interfaces.

 The output displays OSPF hello messages which router R1 has sent received on interface Fa0/1.

 The output displays OSPF hello and LSACK messages which router R1 has sent or received.

Explanation
This combination of commands is known as “Conditional debug” and will filter the debug output based on your conditions. Each condition added, will behave like an ‘And’ operator in Boolean logic. Some examples of the “debug ip ospf hello” are shown below:

NO.203 Drag and drop the characteristic from the left onto the orchestration tools that they describe on the right.

Explanation

NO.204 Drag and drop the characteristics from the left onto the appropriate infrastructure deployment types on the right.

 Loading …

Benefits of obtaining 350-401 Certification:

Implementing Cisco IP Service Provider Networks (IPSPN) Cisco 350-401 Exam PDF will help you in many ways. Cisco 350-401 Dumps are designed to not only prepare you for the test but to help you land a job as an expert. You can work as both the network engineer and the programmer. Cisco Test Engine is used by Cisco 350-401 Certification Engineers to learn new technologies. Majority of the customer of this certification Frequently asks for detailed operating and advantages of obtaining 350-401 Certification. You will be glad to know that answer of your questions are as follows.

1. Shows an understanding of networking concepts and integration with other Cisco technologies. Verify a candidate’s knowledge of managing Cisco routers and switches.

2. Analyze and troubleshoot network issues and implement solutions

3. Understanding of Cisco hardware and software products to configure and manage networks and devices using Cisco IOS-based router, switch, wireless IP router, firewall, IP phones, etc.

4. Prepare to meet the networking requirements in the evolving markets such as wireless communications, security, video surveillance, etc.

5. Support the information security policies and technology requirements to enable secure networks

6. Acquire or enhance knowledge of networking concepts, hardware, or software for skills development

7. Develop the skills to manage, configure and analyze networking technologies in support of business operations through configuration, integration, and troubleshooting. Drag and Drop- IMINS Cisco 350-401 Exam PDF. Spot easily implements the Cisco IOS-based hardware within the network, supporting the existing infrastructure components.

350-401 Dumps for CCNP Enterprise Certified Exam Questions and Answer: https://www.dumpstorrent.com/350-401-exam-dumps-torrent.html