Pass Fortinet NSE6_FWF-6.4 Exam Info and Free Practice Test [Q16-Q39]

NO.16 As standard best practice, which configuration should be performed before configuring FortiAPs using a FortiGate wireless controller?

Create wireless LAN specific policies

Preauthorize APs

Create a custom AP profile

Set the wireless controller country setting

NO.17 Refer to the exhibits.
Exhibit A

Exhibit B

A wireless network has been created to support a group of users in a specific area of a building. The wireless network is configured but users are unable to connect to it. The exhibits show the relevant controller configuration for the APs and the wireless network.
Which two configuration changes will resolve the issue? (Choose two.)

For both interfaces in the wtp-profile, configure set vaps to be “Authors”

Disable intra-vap-privacy for the Authors vap-wireless network

For both interfaces in the wtp-profile, configure vap-all to be manual

Increase the transmission power of the AP radio interfaces

NO.18 Part of the location service registration process is to link FortiAPs in FortiPresence.
Which two management services can configure the discovered AP registration information from the FortiPresence cloud? (Choose two.)

AP Manager

FortiAP Cloud

FortiSwitch

FortiGate

NO.19 Which statement is correct about security profiles on FortiAP devices?

Security profiles on FortiAP devices can use FortiGate subscription to inspect the traffic

Only bridge mode SSIDs can apply the security profiles

Disable DTLS on FortiAP

FortiGate performs inspection the wireless traffic

NO.20 Refer to the exhibits.
Exhibit A

Exhibit B

Exhibit C

A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and IoT devices.
Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.
To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?

Increase the transmission power of the AP radios

Enable frequency handoff on the AP to band steer clients

Reduce the number of wireless networks being broadcast by the AP

Install another AP in the reception area to improve available bandwidth

NO.21 Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)

DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.

DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.

DARRP measurements can be scheduled to occur at specific times.

DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.

NO.22 Which factor is the best indicator of wireless client connection quality?

Downstream link rate, the connection rate for the AP to the client

The receive signal strength (RSS) of the client at the AP

Upstream link rate, the connection rate for the client to the AP

The channel utilization of the channel the client is using

NO.23 Refer to the exhibit.

If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?

Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility

Areas with the signal strength weaker than -68 dB are cut out of the map

Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor

Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.

NO.24 Which two phases are part of the process to plan a wireless design project? (Choose two.)

Project information phase

Hardware selection phase

Site survey phase

Installation phase

NO.25 Refer to the exhibit.

If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?

Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility

Areas with the signal strength weaker than -68 dB are cut out of the map

Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor

Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.

NO.26 How are wireless clients assigned to a dynamic VLAN configured for hash mode?

Using the current number of wireless clients connected to the SSID and the number of IPs available in the least busy VLAN

Using the current number of wireless clients connected to the SSID and the number of clients allocated to each of the VLANs

Using the current number of wireless clients connected to the SSID and the number of VLANs available in the pool

Using the current number of wireless clients connected to the SSID and the group the FortiAP is a member of

NO.27 Refer to the exhibit.

What does the asterisk (*) symbol beside the channel mean?

Indicates channels that can be used only when Radio Resource Provisioning is enabled

Indicates channels that cannot be used because of regulatory channel restrictions

Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)

Indicates channels that are subject to dynamic frequency selection (DFS) regulations

NO.28 As a network administrator, you are responsible for managing an enterprise secure wireless LAN. The controller is based in the United States, and you have been asked to deploy a number of managed APs in a remote office in Germany.
What is the correct way to ensure that the RF channels and transmission power limits are appropriately configured for the remote APs?

Configure the APs individually by overriding the settings in Managed FortiAPs

Configure the controller for the correct country code for Germany

Clone a suitable FortiAP profile and change the county code settings on the profile

Create a new FortiAP profile and change the county code settings on the profile

NO.29 When configuring a wireless network for dynamic VLAN allocation, which three IETF attributes must be supplied by the radius server? (Choose three.)

81 Tunnel-Private-Group-ID

65 Tunnel-Medium-Type

83 Tunnel-Preference

58 Egress-VLAN-Name

64 Tunnel-Type

NO.30 What type of design model does FortiPlanner use in wireless design project?

Architectural model

Predictive model

Analytical model

Integration model

NO.31 Which factor is the best indicator of wireless client connection quality?

Downstream link rate, the connection rate for the AP to the client

The receive signal strength (RSS) of the client at the AP

Upstream link rate, the connection rate for the client to the AP

The channel utilization of the channel the client is using

NO.32 Where in the controller interface can you find a wireless client’s upstream and downstream link rates?

On the AP CLI, using the cw_diag ksta command

On the controller CLI, using the diag wireless-controller wlac -d sta command

On the AP CLI, using the cw_diag -d sta command

On the controller CLI, using the WiFi Client monitor

NO.33 Which statement describes FortiPresence location map functionality?

Provides real-time insight into user movements

Provides real-time insight into user online activity

Provides real-time insight into user purchase activity

Provides real-time insight into user usage stats

NO.34 Which two configurations are compatible for Wireless Single Sign-On (WSSO)? (Choose two.)

A VAP configured for captive portal authentication

A VAP configured for WPA2 or 3 Enterprise

A VAP configured to authenticate locally on FortiGate

A VAP configured to authenticate using a radius server

Pass Fortinet NSE6_FWF-6.4 Exam Info and Free Practice Test [Q16-Q39]

admin

Leave a Reply Cancel reply