[2023] Pass Autodesk ACP-01101 Exam Updated 49 Questions [Q16-Q40]

QUESTION 16

You have a line segment that is 150 units long as shown in the exhibit.
You need the line to be 200 units long without adding any additional linework. The leftmost end of the line must remain in the current position.
What should you do?

QUESTION 17
You need to change the width of a specific polyline without affecting the width of the other polylines in a drawing.
What should you use?

QUESTION 18
In which order should you perform the actions to rotate square (1) to match the angle of square (2).
Move all actions to the answer area and place them in the correct order.

QUESTION 19
What should be typed at the command line in order to start creating a line for drawing reference that starts at a defined point and extends to infinity in the designated direction?

QUESTION 20
You place a red rectangular polyline over a PDF underlay in a drawing, and then use the rectangular polyline as a clipping boundary. The result is shown in the exhibit.
Select whether each statement is True or False.

QUESTION 21
You need to convert the two sets of parallel lines shown in 1 into the objects shown in 2 without repeating the command.
What should you use?

QUESTION 22
You are setting up a drawing layout.
You need to rotate the viewport viewing angle by 90 degrees without rotating the viewport.
What should you do next?

QUESTION 23
Drawings from different sources have been combined and resulted in duplicate background elements that are slightly offset from each other Some of the layer names match and other layers have an E prefix, indicating that they are existing.
To clean up the drawing, the Overkill (OVERKILL) command is used.
Which two settings will resolve the duplicate background and offsetting issues? (Select 2)

QUESTION 24
With an associative array selected as shown in the exhibit, which command will separate the objects into individual objects?

QUESTION 25
Move three applicable commands from the list on the left to the corresponding function on the right.
Commands may be used once or not at all (Select 3)

QUESTION 26
Which two objects support associative dimensions? (Select 2)

QUESTION 27
One of the lines in the drawing is at a 30 degree angle. What’s the quickest way to align the X-axis of the UCS to that line?

QUESTION 28
You have the drawing shown in the exhibit.

You need to place the polygon and the rectangle on the same layer as the circle.
Which command should you use to complete the task in the least number of steps?

QUESTION 29
You start the EXTEND command.
You need to be able to trim several objects quickly without exiting the EXTEND command.
What should you do?

QUESTION 30
You need to create a hatch pattern that looks the same regardless of the viewport scale.
What should you do?

QUESTION 31
You are using the UCS command to set the user coordinate system (UCS)
Select whether each statement is True or False.

QUESTION 32
Refer to the exhibit.

A workstation configuration has been created with the rectangular array command (ARRAYREST. The array is associative and has not been exploded or edited in any way. The dimensions are for reference only To adhere to current office guidelines, the walkways between the workstations need to the made wider.
Which three actions are necessary to meet office layout guidelines? (Choose three.)

QUESTION 33
Refer to the exhibit.

When working on this part created with AutoCAD solids, the dimensions of the shaded planes need to be established.
Which U’CS shows the correct size and shape of the shaded planes?

QUESTION 34
You have the office arrangement shown in exhibit 1. (Refer to the exhibit 1 tab.)

You need a mirror line to create the right-hand office arrangement shown in exhibit 2. (Refer to the exhibit 2 tab.)

Which tool would you use to make sure the mirror line is centered between the two wall lines without adding additional linework?

QUESTION 35

The exhibit shows a workstation arrangement, with horizontal and vertical dimensions, representing the row and column spacings.
Both dimensions have been placed incorrectly, with one origin point of each dimension being placed in the wrong position.
What command should be used to ensure that the dimension objects are placed accurately?