2024 New 156-836 Exam Questions Real CheckPoint Dumps [Q12-Q28]

Explanation
This is not one of the ways to configure a Security Group in a Dual Site environment, because load balancers are not required or supported for the inter-site communication between the Maestro Orchestrators (MHOs).
The MHOs use the Site-Sync port and VLANs to synchronize the resources and connections across the sites.
The three valid scenarios for Dual Site configuration are:
*Direct connectivity between remote site Orchestrators: This scenario requires two orchestrators, one for each site, and a direct connection between them using the site-sync port.
*Two orchestrators on the same site are connected to the remote site orchestrators through two different switches: This scenario requires four orchestrators, two for each site, and a connection between them using the site-sync port and two external switches that support QinQ and MTU increment.
*Two orchestrators on the same site are connected to the remote site orchestrators through one switch: This scenario also requires four orchestrators, two for each site, and a connection between them using the site-sync port and one external switch that support QinQ and MTU increment.
References =
*Maestro Dual Site configuration with a direct connection through L2 switches
*[Dual Site Single Maestro Hyperscale Orchestrator Cluster (Dual Site Single MHO Redundancy)]
*[Maestro Frequently Asked Questions (FAQ)]

Explanation
The Orchestrator MHO-170 supports QSFP and QSFP28 transceivers on its 32x 100 GbE ports. QSFP stands for Quad Small Form-factor Pluggable and QSFP28 is an enhanced version of QSFP that supports up to 28 Gbps per lane. These transceivers can provide high-speed and high-density connectivity for the Maestro environment.
References
*Maestro Hyperscale Orchestrator Datasheet – Check Point Software1, page 2
*Maestro Transceiver & DAC Inventory – Check Point CheckMates

Explanation
This is the correct answer because it describes the difference between using Clish and gClish when working with Maestro. Clish is the Check Point command line shell that allows users to configure and manage the SG members individually. gClish is the global Clish that allows users to run commands on all UP SG members of the current Security Group at once. UP SG members are theones that are in the UP state and have the same policy installed as the SMO Master.
References
*Check Point Certified Maestro Expert (CCME) R81.X Courseware, Module 4: Using the Command Line Interface and WebUI, Lesson 4.3: Global Commands, page 4-11
*Check Point R81 Maestro Administration Guide, Chapter 4: Using the Command Line Interface and WebUI, Section: Global Commands, page 4-9
*Global Expert Mode Commands – Check Point CheckMates

Explanation
Auto-topology is the default distribution mode for Maestro Security Groups. In this mode, the Orchestrator assigns packets to a Security Group Member based on the topology of the port defined in the gateway object.
Each port is either in user mode or network mode depending on the topology. User mode means that the port is connected to the internal network and network mode means that the port is connected to the external network.
The Orchestrator uses a hash function to map each source IP or destination IP to a specific SGM, depending on the mode of the port. This mode ensures that all packets with the same source IP or destination IP are processed by the same SGM, regardless of the port or protocol.
References
*Check Point Certified Maestro Expert (CCME) R81.X Courseware, Module 2: Maestro Security Groups, Lesson 2.4: Traffic Flow, page 2-18
*Check Point R81 Maestro Administration Guide, Chapter 2: Maestro Security Groups, Section: Traffic Distribution, page 2-7
*Lari Luoma | Lead Consultant | Maestro SME | Check Point Evangelist1, slide 16

Explanation
The “asg monitor” command generally would show real-time cluster status of appliances in a security group, focusing on health and operational status.

Explanation
The lldpctl command is a tool to display information about the devices discovered by the Link Layer Discovery Protocol (LLDP) on all ports of the Maestro Orchestrator and the Security Group Members. LLDP is a protocol that enables devices to exchange information about their identity, capabilities, and configuration.
LLDP can help to discover the topology and connectivity of the Maestro environment.
References
*Check Point Certified Maestro Expert (CCME) R81.X Courseware, Module 4: Using the Command Line Interface and WebUI, Lesson 4.2: LLDP, page 4-9
*Check Point R81 Maestro Administration Guide, Chapter 3: Working with Security Group Modules, Section:
LLDP, page 3-9

Explanation
Dual Orchestrators work as an Active-Active cluster, which means that both Orchestrators are active and share the load of the traffic that is sent to and from the Security Group Members (SGMs). Active-Active cluster provides better performance and scalability than Active-Standby cluster, which only uses one Orchestrator at a time and keeps the other as a backup. Active-Active cluster also allows for faster failover and recovery in case of an Orchestrator failure, as the surviving Orchestrator can take over the traffic without interruption.
References
*Maestro Expert (CCME) Course – Check Point Software, page 25
*CheckPoint Certified Maestro Expert (CCME) – Skillzcafe, page 2
*Check Point Certified Maestro Expert (CCME) R81.X – Global Knowledge, page 2

Explanation
The MHO (Maestro Hyperscale Orchestrator) does not require a license by itself, but each SGM (Security Group Module) that is attached to the MHO needs a license. The license type depends on the features and blades that are enabled on the SGM. For example, if the SGM is running VSX, it needs a VSX license.
References:
*Maestro Expert (CCME) Course – Check Point Software, page 71
*Check Point Certified Maestro Expert (CCME) R81.X – Global Knowledge, course outline

Explanation
The Orchestrator is a Maestro component that manages the compute and network resources of the Security Group Modules (SGMs) in a Security Group. It also acts as a load balancer and a network switch, distributing traffic among the SGMs and connecting them to the customer’s network infrastructure.
References:
*Maestro Expert (CCME) Course – Check Point Software, page 41
*Check Point Certified Maestro Expert (CCME) R81.X – Global Knowledge, course outline

Explanation
References =
*[Maestro Frequently Asked Questions (FAQ)]
*Maestro Dual Site configuration with a direct connection through L2 switches
*Dual Site Single Maestro Hyperscale Orchestrator Cluster (Dual Site Single MHO Redundancy)
*CHECK POINT MAESTRO EXPERT

Explanation
References =
*Check Point Maestro R81.X Administration Guide, page 64, section “Correction Layer” 1
*Check Point Maestro R81.X Getting Started Guide, page 26, section “Correction Layer” 2
*Check Point Maestro Under the Hood presentation by Lari Luoma, slide 23
*Check Point Maestro Frequently Asked Questions (FAQ), question 9
1: https://www.manualslib.com/manual/2031661/Check-Point-Maestro-R80-20sp.html 2:
https://sc1.checkpoint.com/documents/R81/WebAdminGuides/EN/CP_R81_Maestro_GettingStarted/html_frame
:
https://community.checkpoint.com/fyrhh23835/attachments/fyrhh23835/maestro/1191/1/Check%20Mates%20M
:
https://supportcenter.checkpoint.com/supportcenter/portal?eventSubmit_doGoviewsolutiondetails=&solutionid=

Explanation
*The Quantum Maestro Orchestrator uses the Distribution Mode to assign incoming traffic to Security Group Members.
*Reference: Working with the Distribution Mode

Explanation
The lldpctl command is a tool to display information about the devices discovered by the Link Layer Discovery Protocol (LLDP) on all ports of the Maestro Orchestrator and the Security Group Members. LLDP is a protocol that enables devices to exchange information about their identity, capabilities, and configuration.
LLDP can help to discover the topology and connectivity of the Maestro environment. The output of lldpctl can show the serial number, appliance model, and orchestrator’s IP of the connected devices, but it cannot show the distribution mode of the Security Group. The distribution mode is the algorithm that determines how the Maestro Orchestrator distributes the traffic among the Security Group Members. To view the distribution mode, other commands such as asg monitor or asg stat can be used.
References
*Check Point Certified Maestro Expert (CCME) R81.X Courseware, Module 4: Using the Command Line Interface and WebUI, Lesson 4.2: LLDP, page 4-9
*Check Point R81 Maestro Administration Guide, Chapter 3: Working with Security Group Modules, Section:
LLDP, page 3-9
*Check Point R81 Maestro Administration Guide, Chapter 2: Maestro Security Groups, Section: Traffic Distribution, page 2-7
*Maestro basic setup documentation – Page 2 – Check Point CheckMates
*Log and Configuration Files – Check Point Software

Explanation
Multi-Version Clustering (MVC) is a feature that allows different versions of Security Gateways to operate in the same cluster and provide seamless failover and load balancing. MVC is supported for Maestro environments as of R81, which means that it is possible to upgrade the Security Groups in a Maestro environment as a Multi-Version Cluster with zero downtime. This requires that the Maestro Orchestrators are upgraded to R81.20 first, and then the Security Groups can be upgraded one by one to R81.20 while maintaining full connectivity and synchronization.
References =
*Check Point R81.20 for Scalable Platforms – Check Point Software
*Maestro Dual Site configuration with a direct connection through L2 switches
*CHECK POINT MAESTRO EXPERT

Explanation
This is the correct answer because it describes the hotfix installation process using gClish on a Maestro Security Group. gClish is the global Clish that allows users to run commands on all UP SG members of the current Security Group at once. When a hotfix is applied using gClish, the SG members are divided into two logical groups: “A” and “B”. The members of group “A” install the hotfix and reboot first, while the members of group “B” wait for their turn. After all the members of group “A” are back online, the members of group
“B” install the hotfix and reboot.This way, the SG maintains high availability and does not cause an outage.
References
*Check Point Certified Maestro Expert (CCME) R81.X Courseware, Module 4: Using the Command Line Interface and WebUI, Lesson 4.3: Global Commands, page 4-11
*Check Point R81 Maestro Administration Guide, Chapter 4: Using the Command Line Interface and WebUI, Section: Global Commands, page 4-9
*Global Expert Mode Commands – Check Point CheckMates