Best Ericsson ECP-206 2023 Training With 62 QA’s [Q37-Q54]

Explanation
The command that is used to begin making changes to the router settings in an Ericsson Router 6000 is configure. This command enters the configuration mode, where various commands can be used to modify the router parameters, such as interfaces, protocols, services, security, etc. To exit the configuration mode, the command end can be used. To save the changes made in the configuration mode, the command commit can be used56.
References: Router 6000 Series – Ericsson, Ericsson Router 6000 series (6471/6672/6675) Commands for
2G/3G/4G/5G technologies… – YouTube

Explanation
OSPF runs directly on IP, while IS-IS runs directly on Ethernet. This means that OSPF uses IP addresses to identify routers and links, while IS-IS uses MAC addresses or other link-layer identifiers. OSPF also requires an IP header for each packet, while IS-IS does not. Both OSPF and IS-IS are link state protocols, which means that they flood information about the network topology to all routers in the same area or domain. References: Ericsson IP Networking – Routing Protocols, Ericsson Router 6000 Series – Ericsson

Explanation
Link-state routing protocols are one of the two main classes of routing protocols used in packet switching networks for computer communications, the other being distance-vector routing protocols. Examples of link-state routing protocols include Open Shortest Path First (OSPF) and Intermediate System to Intermediate System (IS-IS). The basic concept of link-state routing is that every node constructs a map of the connectivity to the network, in the form of a graph, showing which nodes are connected to which other nodes. Each node then independently calculates the next best logical path from it to every possible destination in the network.
Each collection of best paths will then form each node’s routing table.
Two statements that are true about link-state routing protocols are:
The advertisement exchange is mainly triggered by a change in the network. Link-state routing protocols use a flooding mechanism to distribute information about the network topology to all routers in the same area or domain. This information is encapsulated in link-state packets (LSPs) or link-state advertisements (LSAs), which contain information about the router, its directly connected links, and the state of those links. LSPs or LSAs are sent only when there is a change in the topology, such as a link failure or recovery, or when a periodic refresh timer expires. This way, link-state routing protocols can quickly adapt to network changes and maintain an accurate and consistent view of the network.
Each router uses a reliable update mechanism to exchange topology information with its neighbors.
Link-state routing protocols use a reliable update mechanism to ensure that all routers receive and acknowledge the LSPs or LSAs sent by their neighbors. This mechanism involves sending hello messages to establish and maintain adjacencies with neighbors, sending acknowledgment messages to confirm the receipt of LSPs or LSAs, and requesting missing or outdated LSPs or LSAs from neighbors.
This mechanism ensures that all routers have a synchronized database of LSPs or LSAs, which is used to build a complete network connectivity map and to calculate the shortest path to destinations.
References: Link-state routing protocol – Wikipedia, Ericsson IP Networking – Routing Protocols

Explanation
LDP relies on IGP for all routing-related decisions. LDP is a protocol that distributes labels in an MPLS environment, but it does not perform any routing functions. LDP uses the underlying routing information provided by an IGP, such as OSPF or IS-IS, to forward label packets. LDP and IGP do not exchange their databases at regular intervals, but rather use hello messages to maintain adjacencies and sessions. References: Ericsson IP Networking – Routing Protocols, Label Distribution Protocol – Wikipedia

Explanation
Two statements that are true regarding the LSP are:
The LSP refers to a sequence of routers that forward the MPLS packet based on labels. An LSP is a Label Switched Path, which is a path through an MPLS network that is established by signaling protocols such as LDP or RSVP-TE. An LSP consists of a sequence of routers (called Label Switching Routers or LSRs) that forward packets based on labels rather than IP addresses. Labels are short fixed-length identifiers that are attached to packets at the ingress router and removed at the egress router. Labels can be swapped or popped at intermediate routers according to their label forwarding tables78.
The LSP refers to a sequence of routers that add, remove, or change label values along the path. As mentioned above, an LSP consists of a sequence of routers that forward packets based on labels. Along the path, different routers may perform different operations on the labels depending on their role and configuration. The ingress router adds one or more labels to the packet before sending it into the MPLS network. The egress router removes all labels from the packet before sending it out of the MPLS network. The intermediate routers may swap one label with another label according to their label forwarding tables. This process is called label switching78.
References: MPLS Fundamentals: 3 – MPLS Packet Forwarding, Multiprotocol Label Switching – Wikipedia

Explanation
The correct abbreviation for the IP address BFEA:DACA:0000:0000:9390:0000:0000:D91 is BFEA:DACA::9390:0:D91. IPv6 addresses are represented in hexadecimal notation, with eight 16-bit segments separated by colons. To simplify the address representation, IPv6 supports two types of abbreviations. The first abbreviation allows us to skip leading zeros within a segment, while the second abbreviation allows us to drop one or more consecutive segments that contain only zeros, using a double colon (::) instead. However, the double colon can be used only once in an address, to avoid ambiguity34.
References: IPv6 Address Types, Notation, and Structure Explained, IPv6 address – Wikipedia

Explanation
The action that will influence BGP route selection within your AS is changing the default value of the local preference attribute. The local preference attribute is used to indicate the preference of a path among multiple paths learned from different external BGP neighbors or autonomous systems (ASes). The higher the local preference value, the more preferred the path is within your AS, and vice versa. The default value of local preference is 100, but you can change it using route maps or other configuration methods on your BGP routers. References: Ericsson IP Networking – Routing Protocols, BGP Attributes and Path Selection, BGP Local Preference Attribute: Controlling Traffic Like a Pro

Explanation
In the exhibit, the action performed by router R3 for traffic arriving from router R2 towards router R4 is PHP, which stands for penultimate hop popping. PHP is a process in which the penultimate hop router (the router before the egress router) removes the top label from an MPLS packet before forwarding it to the egress router.
This reduces the label stack depth of the packet and relieves the egress router from performing a label lookup operation. In the exhibit, router R3 is the penultimate hop for traffic arriving from router R2 towards router R4. Router R3 will perform a PHP operation, removing the top label from the incoming packet before forwarding it to router R478.
References: PHP Tutorial – W3Schools, PHP: Downloads

Explanation
Referring to the exhibit, the two Ericsson routers that support the 100GE interface are Router 6675 and Router
6672. The 100GE interface is a high-speed Ethernet interface that operates at 100 gigabits per second. The Ericsson Router 6000 series is a family ofrouters that provide IP transport for mobile and fixed networks. The Router 6675 is a 5G combined access and E-RAN switch with 100GE interfaces and 320Gb forwarding capacity. The Router 6672 is a high-capacity metro aggregation router with 100GE interfaces and 1.6Tb forwarding capacity12.
References: Router 6000 Series – Ericsson, New Ericsson Router 6000 series couples radio and IP transport for
5G future – Global Brands Magazine

Explanation
Two protocols that apply to both IPv4 and IPv6 are:
SNMP: This stands for Simple Network Management Protocol, which is a protocol that allows network administrators to monitor and manage network devices such as routers, switches, servers, printers, etc.
SNMP uses a client-server model, where an SNMP manager (client) can query or configure an SNMP agent (server) on a network device using SNMP messages. SNMP can operate over both IPv4 and IPv6 networks56.
DNS: This stands for Domain Name System, which is a protocol that translates human-readable domain names (such as www.example.com) into numerical IPaddresses (such as 192.0.2.1 or 2001:db8::1) that identify network devices. DNS uses a hierarchical distributed database of name servers that store and resolve domain names and IP addresses. DNS can support both IPv4 and IPv6 addresses78.
References: Simple Network Management Protocol – Wikipedia, SNMP over IPv6 – Cisco, Domain Name System – Wikipedia, DNS for IPv6 – Cisco

Explanation
The CLI command to obtain the software version in Ericsson Router 6000 products is show version. This command displays information about the software release, the hardware model, the serial number, the uptime, and the boot image of the router. References: [ERICSSON SMARTEDGE 600 HARDWARE MANUAL Pdf Download | ManualsLib], Ericsson Router 6000 Series – Ericsson

Explanation
iBGP works by exchanging routing information between two or more routers within an AS. Each router sends its own routing table to its neighbors, which contains information about the networks it knows and how they can be reached from that router. By default, iBGP neighbors only share BGP routes learned from eBGP neighbors, which are routers in different ASes. This is because iBGP assumes that all routers within an AS have consistent internal routing information provided by an IGP, such as OSPF or IS-IS. Therefore, iBGP neighbors do not need to share IP address information of loopbackinterfaces or directly connected interfaces, unless explicitly configured to do so by using commands such as neighbor update-source or network.
References: iBGP Ultimate Guide | How iBGP Is Different From eBGP, Ericsson IP Networking – Routing Protocols

Explanation
To differentiate traffic types for the purpose of prioritization in their Ethernet LAN and IP/MPLS backbone, an operator can use the following three fields:
Traffic Class (TC): This is a 3-bit field in the MPLS label that can be used to indicate the priority or class of service (CoS) of the packet. The TC field can be mapped to the DSCP field in the IP header or the PCP field in the Ethernet header. The TC field can be used by MPLS routers to apply different per-hop behaviors (PHBs) such as queuing, scheduling, and dropping policies to different traffic classes12.
DSCP: This is a 6-bit field in the IP header that can be used to mark packets according to the differentiated services (DiffServ) model. The DSCP field can indicate the per-hop behavior (PHB) that the packet should receive at each router along its path. The DSCP field can be mapped to the TC field in the MPLS label or the PCP field in the Ethernet header. The DSCP field can be used by IP routers to provide QoS for different traffic types34.
PCP: This is a 3-bit field in the Ethernet header that can be used to mark packets according to the IEEE
802.1Q standard. The PCP field can indicate the priority or class of service (CoS) of the packet on an Ethernet LAN. The PCP field can be mapped to the TC field in the MPLS label or the DSCP field in the IP header. The PCP field can be used by Ethernet switches to provide QoS for different traffic types56.
References: MPLS Traffic Engineering – DiffServ-Aware Traffic Engineering, MPLS Traffic Engineering – DiffServ-Aware Traffic Engineering Configuration Guide, Differentiated services – Wikipedia, DSCP and Precedence Values – Cisco, 802.1Q VLAN IDs and Ethernet Interface Types – Juniper Networks, Introduction to Virtual LANs (VLANs) and Tagging – Ubiquiti Support and Help Center

Explanation
A P router is a provider router that is part of the service provider’s core network in an MPLS environment. A P router does not have any customer routes or VPN information, but only has information about how to reach other P routers and PE routers in the same MPLS domain. A P router performs label switching, which means that it forwards labeled packets based on their top label in the label stack. A P router can perform two possible label actions:
Swap: The P router replaces the incoming label with a new label that corresponds to the next hop along the label-switched path (LSP). The new label is determined by looking up the label forwarding information base (LFIB) based on the incoming label and interface.
PHP: The P router removes the top label from the packet at the penultimate hop before reaching the egress PE router. This is done to avoid an extra lookup on the egress PE router, which can forward the packet based on its IP header or another label in the stack.
A P router does not perform push or drop actions on labels. A push action means adding one or more labels to the packet, which is done by an ingress PE router when initiating an LSP. A drop action means discarding a packet, which is done by any router when there is no matching entry in its LFIB or routing table. References: Provider (P) Router in IP MPLS Network – Cisco Community, MPLS Fundamentals: Forwarding Labeled Packets – Cisco Press, MPLS Label Switching | MPLS Operation | Push, Swap,Push IPCisco

Explanation
Referring to the exhibit, the service provider should implement L3VPN using the MP-BGP protocol to connect the sites for two customers (indicated in red and green in theexhibit). L3VPN is a type of VPN that uses MPLS to provide IP connectivity between customer sites across a service provider network. L3VPN allows customers to use overlapping or identical IP addresses without causing conflicts or requiring NAT. L3VPN uses MP-BGP to exchange VPN routes between PE routers, which are routers that connect customer networks to the service provider network. MP-BGP is an extension of BGP that can carry multiple address families, such as VPNv4 or VPNv6, along with additional attributes, such as route distinguisher (RD) and route target (RT). RD is used to make customer routes unique within the service provider network, while RT is used to control which routes are imported or exported between different VPNs3 .
References: L3VPN – Layer 3 Virtual Private Networks – Mpirical, [Use of MP-BGP Extensions for IPv6 Interdomain Routing]

Explanation
The Area ID to which the router belongs is 49.00F0.0100. The Area ID is a variable-length field in the NSAP address that identifies the area to which the router belongs. The Area ID can be between 1 and 13 bytes long, but it must start and end with an octet (8 bits). The NSAP address is composed of three parts: the authority and format identifier (AFI), the area ID, and the system ID. The AFI is a one-octet field that indicates the format and authority of the rest of the address. The system ID is a fixed-length field of six octets that uniquely identifies the router within an area. The NSAP address also has a network selector (NSEL) field, which is a one-octet field that identifies the network layer service to which a packet should be sent. For IS-IS routers, the NSEL must always be 00.
In this question, the NSAP address is 49.00F0.0100.5012.3010.00. This means that:
The AFI is 49, which indicates a private address.
The Area ID is 00F0.0100, which is four octets long and starts and ends with an octet.
The system ID is 5012.3010, which is six octets long and identifies the router within the area.
The NSEL is 00, which indicates IS-IS.
Therefore, the answer is B.
References: Ericsson IP Networking – Routing Protocols, IS-IS NSAP address – Cisco Community, Understanding IS-IS NSAP Addresses – Todd Lammle, LLC, IS-IS – Nokia, Network service access point address – Wikipedia

Explanation
The protocol that would be used to bundle multiple Ethernet ports into a virtual link with an aggregated bandwidth is LACP, which stands for Link Aggregation Control Protocol. LACP is a protocol that allows two or more devices to negotiate the formation of a link aggregation group (LAG), also known as an EtherChannel or a port channel. A LAG combines multiple physical links into one logical link that provides increased bandwidth, load balancing, and redundancy. LACP is defined in IEEE 802.3ad and 802.1AX standards12.
References: Link Aggregation Control Protocol – Wikipedia, What is “link aggregation” and how does it benefit your network? | PC Gamer

Explanation
The conceptual table created by routing protocols that is used when processing an IP packet is the forwarding information base (FIB). The FIB is a table that contains the bestroutes to reach each destination network prefix, along with the outgoing interface and the next-hop address for each route. The FIB is derived from the routing information base (RIB), which is a table that contains all the routes learned from different routing protocols and sources. The FIB is used by the router to make fast forwarding decisions for each incoming packet, based on its destination address12.
References: Security Hardening Checklist Guide for Cisco Routers/Switches in 10 Steps, VLAN – Wikipedia