Prepare for the Actual Aruba Certified Switching Associate (ACSA) HPE6-A86 Exam Practice Materials Collection [Q19-Q36]

QUESTION 19
Which user group exists by default on an HPE Aruba Networking CX 6400 Series switch?

QUESTION 20
A Network Operator is configuring QoS on an HPE Aruba Networking CX switch. The operator needs to classify traffic based on the application being used, such as distinguishing between HTTP and FTP traffic.
Which of the following is used to identify the application at Layer 4 for QoS classification?

QUESTION 21
A switch port connected to an end-user workstation should never receive Bridge Protocol Data Units (BPDUs). Which feature helps protect the network if a switch is accidentally connected to that port?

QUESTION 22
A Junior Network Engineer is designing a small office network and has been assigned the IP address block 192.168.100.0/24. They need to create at least 5 separate subnets for different departments, with each subnet supporting at least 25 hosts. Which subnet mask would successfully meet these requirements?

QUESTION 23
A Security Analyst is explaining to a colleague why a standard switch cannot, by itself, stop the spread of a virus between two computers that are in the same VLAN. Which statements accurately describe the function of a standard Layer 2 switch within the OSI model? (Select all that apply.)

QUESTION 24
The customer plans to roll out new HPE Aruba Networking CX 6000 and CX 6100 switches to replace the existing AOS-S switches. To make the deployment include fewer manual tasks, the customer has asked how Zero Touch Provisioning, or ZTP, would help with the transition.
Select the correct statement about ZTP.

QUESTION 25
Which statement describes static routing?

QUESTION 26
What is the default subnet mask for an IPv4 Class C network?

QUESTION 27
A customer requires a network upgrade to replace their existing core switches. The new solution must support
100G speeds to the aggregation layer, with the ability to scale to a 12U chassis.
Which HPE Aruba Networking CX switch model would you initially propose?

QUESTION 28
You are discussing a solution for a three-tier hierarchy with HPE Aruba Networking CX switches with a customer. Which statement matches this design?

QUESTION 29
A network administrator is designing a network with a redundant path between two distribution switches. To prevent Layer 2 loops while allowing for fast failover, the administrator has enabled Rapid Spanning Tree Protocol (RSTP).
What is the primary advantage of using RSTP (802.1w) over the original Spanning Tree Protocol (STP, 802.1D)?

QUESTION 30
While investigating a fault, you discovered that a LAG interface from an aggregation switch was connected to two different access switches.
How can you re-configure the LAG interface so it will only come up if connected to the same access switch?

QUESTION 31
A Solutions Architect is conducting a final validation of a newly installed core switch. The architect needs to quickly get a high-level summary of the switch’s health and resources. Which troubleshooting commands would provide a good “dashboard” view of the switch’s overall health?
(Select all that apply.)

QUESTION 32
In the partial example of the LLDP output below:

Port: 1/1/25
Neighbor Entries : 1
Neighbor Entries Deleted : 0
Neighbor Entries Dropped : 0
Neighbor Entries Aged-Out : 0
Neighbor System-Name :
Chassis Capabilities Available : Bridge, Router
Chassis Capabilities Enabled : Bridge, Router
Neighbor Port-ID : 1/1/51
Neighbor Port-Desc : 1/1/51
Neighbor Port VLANID : 1
Neighbor Port VLAN Name :
Neighbor Port MFS :
Link aggregation supported : Information Not Available
Link aggregation enabled : No
Aggregation port ID : 0
TTL : 120
Neighbor Mac-Phy details
Neighbor Auto-Neg Supported : true
Neighbor Auto-Neg Enabled : false
Neighbor Auto-Neg Advertised : Other
Neighbor MAU type : 10GIGBASER
What can be validated based on the provided output?

QUESTION 33
Which protocols can be used to control administrative access to HPE Aruba Networking OS-CX switches? (Choose two.)

QUESTION 34
When explaining the HPE Aruba Networking Virtual Switching features, which statement about VSX is true?

QUESTION 35
A Network Operator is reviewing the VLAN configuration on an AOS-CX switch.
show vlan
VLAN ID Name Status
– — —
1 DEFAULT_VLAN Active
10 Sales Active
20 Engineering Active
30 Marketing Active
What is the primary purpose of creating these separate VLANs?

QUESTION 36
You have configured the following on a Core-1 HPE Aruba Networking CX switch for primary and secondary ISP connectivity:
Core-1(config)# ip route 0.0.0.0/0 10.1.251.2
Core-1(config)# ip route 0.0.0.0/0 10.1.252.2 distance 10
The default route via 10.1.251.2 stopped working, and no failover happened. The ISP reported a broken fiber on the path of an upstream device.
In what condition should the route fail over to the 10.1.252.2 router?